Rki-instruments RX-517 Bedienungsanleitung

PT0E-0730 RIKEN PORTABLE COMBINATION GAS DETECTOR MODEL ＲＸ−５１６ ＲＸ−５１７ OPERATION MANUAL MARINE USE Precaution in operation

PT0E-0730 9３−３．Start-up and end-up When press power switch for 3 sec, the power gets on and this shall start up sequencing the program of the volta

PT0E-0730 10３−４．Flow monitor check When the power gets ON, the pump shall start operation check that suction works properly by filter tube with flo

PT0E-0730 11＜FLOW CHART OF ZERO POINT ADJ＞ ZERO MODE DISPLAYHOLD KEY ADJ ZERO OK 《Zero set OK》 ZERO SET OK FAIL ZERO ・Press ZERO key for 3 sec. Pre

PT0E-0730 12３−６．Operational procedure Approach the sampling hose to the sampling site for measurement and leave sampling gas sucked. ・Take care t

PT0E-0730 13３−７．Peak SW value mode When press PEAK SW during operation, the peak valve from power on to the current point (HC, H2S = MAX, O2=MIN) s

PT0E-0730 14 ３−９．Operation finished （1）Treatment after operation Wind up sampling hose so treat it can not be twisted and bent. Supply fresh air

PT0E-0730 15３−１０．Practical application (1) Tank inside of crude oil tanker By use of sampling hose with plummet, it is available to monitor the gas

PT0E-0730 16《Interference measures in inert gas》 In the component of inert gas, a lot of interference gas may be present. When it should be present s

PT0E-0730 17４−３．Trouble display （1）Low flow alarm ・When low flow trouble triggers, “LOW FLOW” is displayed and pump stops working. ・Buzzer sounds con

PT0E-0730 18 （3）System trouble alarm ・When the program is troubled, “SYSTEM FAIL” will be shown. ・Buzzer will sound continuously. ・After “SYSTEM FAIL

PT0E-0730 1 In the beginning It is of our great pleasure to purchase Riken portable combination gas detector model RX-516/RX-517 this time. This

PT0E-0730 19５．Each function ５−１．Operation mode control Operation mode HOLD KEY D A T E T I M E ①1st alarm display ②2nd alarm Day/time display Data l

PT0E-0730 20５−１−１．Alarm setting 1st alarm display PEAK key M ‐ P A S S W O R D ・First, 1st alarm point shall be shown on the display. ・Change 『＋』

PT0E-0730 21５−１−２．Date/time setting ５−2．LCD back light LCD back light will be on in the following ・Initial clear ： Light on ・Operation on

PT0E-0730 22５−3．Data logger Data logger function has following 5 kinds. （1）Interval trend The change of measuring gas shall be recorded until the po

PT0E-0730 23６．Maintenance check For this correct operation, follow to the following procedure. ６−１．Battery replacement When replace the

PT0E-0730 24６−２．Gas calibration (Span adjustment) ZERO key PUMP key ・ Hold and pressing ZERO and PUMP key similtaneously in the operation mode

PT0E-0730 25 《Handling of sampling bag and canned gas》 ① Sample the cal gas into sampling bag from canned gas. ② Sampling bag with cal g

PT0E-0730 26《Cal gas make-up by H2S gas checker CK-82》 ① Take out 1 pce. ampoule from accessory ampoule pack. ② Check that the rubber caps are fix

PT0E-0730 27６−３．Filter replacement For filter (cotton) inside of filter with flow monitor, check it before use and when it gets dirty, replace it.

PT0E-0730 28６−６．The replacement of parts The following parts have a life and each, regular replacement shall be recommended. When replace, contac

PT0E-0730 2 C O N T E N T S １．Caution in operation ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ３ ２．Name of each part・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ４ ３．Operatio

PT0E-0730 29６−７．Storage or treatment not to use for a long period The instrument shall be kept in the following condition. Temp ：10∼30℃ Humidity ：30∼

PT0E-0730 30８．Trouble shooting This trouble shooting does not mention all the trouble causes. The following is mentioned briefly by picking up the

PT0E-0730 31９．Definition of words Vol% Gas density is expressed by the unit of a part. ppm Gas density is expressed by the unit of a part per.

PT0E-0730 32１０．Specifications Refer to the specifications for separate catalog overleaf. Model RX-516 (HC/O2/H2S 0-100.0ppm) , RX-517 (HC/O2/H2S 0

PT0E-0730 33１１．Detection principle １１−１．NDIR method (Non-Dispersive Infrared) The model is based on NDIR method (Non-Dispersive Infrared) and this st

PT0E-0730 34 １１−３．ELECTRO-CHEMICAL CELL method This gas detector applies an electrochemical sensor. The sample gas is electrolyzed by the electrolyze

PT0E-0730 3１．Caution in operation To maintain the function for safety, follow the following instruction. Warning

PT0E-0730 4２．Name of each part ①POWER／ENTER SW This is used for power ON/OFF and entering the figure. ②PUMP／− SW This is used when make the pump

PT0E-0730 5《Display of RX-516／517》 Hydro carbon 「HC」 RX-516／RX-517 Hydrogen sulfide（Low）「H2S」 Oxygen「OXY」RX-517 Hydrogen sulfide（High）「H2S」＊Caut

PT0E-0730 6【Standard accessories】 ①Carrying case with shoulder strap ②Filter tube with flow monitor and junction tube ③G

PT0E-0730 7 【Optional accessories】 ①Gas sampling hose 30m with plummet ②Gas sampling hose 30m with float type sampling head

PT0E-0730 8３．Operation ３−１．Check item before operation RX-516 or 517 instrument： ・Check that there is no damage for display unit etc. Filter tube wit