Rki-instruments SDM-2009 Bedienungsanleitung

www.rkiinstruments.com SDM-2009 Docking StationStandalone ConfigurationOperator’s ManualPart Number: 71-0261RKRevision: 0Released: 8/12/13

6 • USB CableUSB CableA Type A to Type B USB cable is provided with the docking station. It is only for use with the PC Controlled configuration. It

Air Filter and Sample Tubing • 7WARNING: Do not use an exhaust tube that is longer than 10 feet. The increased flow restriction caused by a longer tu

8 • Instrument CradleInstrument CradleThe instrument cradle is a recessed area on the top of the SM-2009 that is designed to accept the GX-2009. Inse

Back Panel • 9Back PanelThe back panel includes the power jack, sample fittings, and a USB PC connector. Power JackThe power jack is located in the b

10 • Control PanelControl PanelThe control panel is used to setup and operate the docking station in the Standalone configuration. It is located at t

Control Panel • 11CAL S • Initiates a calibration• Cancels a calibration• Clears data from docking station memory (when used with COPY button)• Move

12 • Front PanelFront PanelA type A USB port is located on the front of the docking station. This port can be used to save calibration and bump test

Overview • 13Chapter 3: Preparing to Use the SDM-2009OverviewThere are four tasks that must be completed before you can begin to use the SDM-2009: ha

14 • Setting the Operational Parameters in Edit ModeSetting the Operational Parameters in Edit ModeOnce the hardware has been assembled, use Edit Mod

Setting the Operational Parameters in Edit Mode • 15Air Sample Time (AIr)The air sample time can be set separately for bump testing and calibration.

WarrantyWarrantyRKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in materials and workmanship, and performance f

16 • Setting the Operational Parameters in Edit ModeTurning on the SDM-2009 with an InstrumentDo the following to turn on the SDM-2009 and establish

Setting the Operational Parameters in Edit Mode • 17screen shown above in step 6. The CHARGE LED will begin to blink green.• When Cal Limit Display i

18 • Setting the Operational Parameters in Edit Mode 4. If you wish to cancel setting the bump test parameters or were just viewing the parameters to

Setting the Operational Parameters in Edit Mode • 19 9. When you are done setting the parameters, use the BUMP T button to scroll past the AUTO--C pa

20 • Setting the Operational Parameters in Edit ModeParameters” on page 14. 5. Use the BUMP T and CAL S buttons to scroll through the different cal

Connecting Calibration Gas • 21Connecting Calibration Gas The GAS fitting on the back of the docking station is designed to be used with a calibratio

22 • Installing the Single Module Data Viewer SoftwareInstalling the Single Module Data Viewer Software 1. Launch Windows®. 2. Exit from all applicat

Overview • 23Chapter 4: OperationOverviewWhen you have completed the tasks in "Chapter 3: Preparing to Use the SDM-2009", you are ready to

24 • Bump Testing a GX-2009and the SDM-2009 occurs, the home screen will appear on the instrument display at the end of the startup sequence. The aut

Bump Testing a GX-2009 • 25 9. Verify that the appropriate calibration gas cylinder is connected to the GAS fitting on the back of the SDM-2009. See

Table of ContentsTable of ContentsChapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 • Bump Testing a GX-2009• If one or more of the sensors fails the fresh air adjustment, the SDM-2009 will abort the bump test and will not apply c

Bump Testing a GX-2009 • 27for a description of calibration results. 16. The SDM-2009 will then purge the system with fresh air for the time defined

28 • Bump Testing a GX-2009 Figure 15: Screen Indication for Failed Bump Test and Failed Calibration 18. After a successful or failed bump test,• To

Calibrating a GX-2009 • 29a USB flash drive. 20. Remove the GX-2009 from the SDM-2009. 21. If you wish to bump test additional instruments, repeat s

30 • Calibrating a GX-2009NOTE: The screen shown above applies to a 4-channel GX-2009. If your GX-2009 has less than 4 channels, the inactive channel

Calibrating a GX-2009 • 31 9. Press and hold the CAL S button until the CAL S LED turns on (about one second) then release it. During the calibration

32 • Calibrating a GX-2009 13. The SDM-2009 will apply calibration gas to the instrument for the time defined by the GAS calibration parameter. 14

Calibrating a GX-2009 • 33hold the EDIT ENTER and POWER buttons simultaneously for about one second and then release them. To avoid accidentally ente

34 • TroubleshootingTroubleshootingNOTE: This troubleshooting guide describes SDM-2009 problems only. See the GX-2009 Operator’s Manual for problems

Troubleshooting • 35• No IR connection between instrument and SDM-2009• SDM-2009 is not turned on.• The instrument is not correctly inserted into the

Table of ContentsInstalling the Single Module Data Viewer Software. . . . . . . . . . . . . . . . . . . . . . . 22Chapter 4: Operation. . . . . . . .

36 • Charging an Instrument in a Docking StationCharging an Instrument in a Docking StationThe SDM-2009 can be used to charge the rechargeable batter

Charging an Instrument in a Docking Station • 37Recharging the Batteries Without Performing Any Operations 1. Confirm that the AC adapter is connecte

38 • Calibration and Bump Test RecordsCalibration and Bump Test RecordsThe SDM-2009 saves a record of each bump test and calibration performed. It is

Calibration and Bump Test Records • 39SDM-2009 will take a few seconds to determine how much memory is available in the flash drive. • If the flash d

40 • Calibration and Bump Test RecordsThe files that an SDM-2009 saves to a USB flash drive are structured so that they can be imported into a databa

Overview • 41Chapter 5: Single Module Data Viewer ProgramOverviewThe Single Module Data Viewer Program is used to view, organize, and print bump test

42 • Using the Single Module Data Viewer ProgramNOTE: When you start the Single Module Data Viewer Program for the first time, there will be no data

Using the Single Module Data Viewer Program • 43• View the bump test and calibration data saved in the database.• Delete data.• Print bump test or ca

44 • Using the Single Module Data Viewer ProgramOrganizing the Data When viewing the data, it can be organized in two ways: 1. Base View FormatIn bas

Using the Single Module Data Viewer Program • 45 2. ID View FormatIn ID view format, the data can be organized by one or more of the following items

Overview • 1Chapter 1: IntroductionOverviewThis chapter briefly describes the SDM-2009 Docking Station and the Single Module Data Viewer Program. Thi

46 • Using the Single Module Data Viewer Program 2. When an item no longer has a (+) or (-) symbol next to it, single click it and the contents of th

Using the Single Module Data Viewer Program • 47If you organize the data by date, then folders organized by year/month appear in the left side of the

48 • Using the Single Module Data Viewer ProgramIf you are viewing data in ID view format, expand the folders in the left side of the window until th

Using the Single Module Data Viewer Program • 49appear showing the selected printer and confirming if you want to print. Verify that the selected pri

50 • Using the Single Module Data Viewer Program 3. Enter the password and click OK. The factory set password is “ABCDE” and is case sensitive. A con

Spare Parts List • 51 4. Enter the new password and click the New Password button. A confirmation window will appear prompting you for the new passwo

Spare Parts List • 5249-2058RK-04 4-port AC adapter71-0261RK Operator’s Manual, SDM-2009 Docking Station Standalone Configuration (this document)71-0

2 • System RequirementsCAUTION: The GX-2009 detects oxygen deficiency and elevated levels of oxygen, combustible gases, carbon monoxide, and hydrogen

Specifications • 3SpecificationsTable 1: SDM-2009 SpecificationsInput Power 12 VDCNOTE: AC Adapter with 100 - 240 VAC, 50/60 Hz, 0.6A input and 12 VD

4 • About this ManualAbout this ManualThe SDM-2009 Docking Station Standalone Configuration Operator’s Manual uses the following conventions for note

Overview • 5Chapter 2: DescriptionOverviewThis section describes the SDM-2009 docking station. It is designed to be used on a table top and consists